Data centers
Antivibration mounts, seals and cable entries for data center gensets, transformers, chillers, CDUs and prefabricated modules – engineered by Trelleborg and supported by application engineers close to your sites.
Why it matters
Chillers, dry coolers and gensets run 24/7, and data center sites face increasingly strict noise limits from neighbors and authorities.
Rotating equipment on roofs and slabs carries vibration and hum into the building unless every path is isolated – frames, pipes and cable routes.
Direct-to-chip liquid cooling brings coolant to every rack. In a CDU or quick-disconnect coupling, a failed seal means an outage.
Prefabricated modules, skids and power rooms travel long distances by road and sea. For many, transit is the most severe load they ever see.
How we work with you
For engineering teams building gensets, chillers, CRAH units, CDUs, switchgear and battery storage. Our application engineers size isolation for your frame, supply samples for type testing and support you through to series release.
Request an application assessmentWhat you get
For design-standards teams, MEP consultants and commissioning agents writing requirements for noise, vibration and equipment protection.
Request technical documentationWhat you get
For prefab integrators, skid builders and heavy-haul project teams. Transit shock is often the most severe load a module ever sees.
Discuss a module projectWhat you get
For OEM service organizations, distributors and facility teams maintaining gensets, chillers and pumps.
Ask about replacement partsWhat you get
Applications
Select a zone to see where Trelleborg antivibration, sealing and cable entry solutions are used.
Standby gensets carry the full IT load when the grid fails. Each set is a large rotating mass whose vibration must stay out of the building – and whose fuel, oil and coolant systems must stay sealed.
AntivibrationEngine and alternator mounts, radiator and control-panel isolators, belly-tank pads for double isolation.
SealingFuel, lube-oil, coolant and exhaust seals in NBR, HNBR and FKM.
Cable entryCable entry plates for control panels and enclosures.
Transformers, switchgear and batteries increasingly arrive as prefabricated skids. Each one needs vibration control, sealing and cable entry.
AntivibrationElastomer pads and sandwich mounts under tank and skid; transport shock protection.
SealingOil-resistant cover, bushing and radiator gaskets.
Cable entryCable box and marshalling-kiosk entries.
Cable entryCable entry plates, modular and splitting systems (IP66/67, UL94 V-0) for bottom and wall entry.
AntivibrationTransport mounts for skid shipping and leveling mounts.
SealingDoor and panel gaskets.
AntivibrationRack feet, inter-tray pads and container transport mounts.
Cable entryContainer and rack cable entries, IP66/67 and halogen-free.
SealingDoor, HVAC and vent seals.
Chillers, dry coolers and pumps run 24/7 and are often the loudest equipment on site. Liquid cooling moves more heat rejection to large fan arrays and pump loops.
AntivibrationBase-rail mounts under the frame; compressor and fan isolators.
SealingCompressor lip seals, gaskets and valve seats.
Cable entryControl-cabinet cable entries.
AntivibrationLeg and frame isolators; fan-motor mounts.
Cable entryFan-array power and control entries.
SealingFan-bearing and gearbox seals for towers.
AntivibrationInertia-base and pump mounts; flexible pipe connectors.
SealingMechanical-seal elastomers, O-rings and flange gaskets.
High-density halls combine liquid-cooled racks, CDUs at every row and fan walls for the remaining air load – with dense cabling throughout.
AntivibrationLeveling cabinet feet and battery-rack pads.
Cable entryBottom-entry plates and split entries for UPS and battery cabinets.
SealingCabinet and vent seals.
AntivibrationFan-sled isolators and cabinet feet.
Cable entryPower and sensor cable entries.
SealingQuick-disconnect O-rings, CDU pump and valve seals, plate heat exchanger gaskets.
AntivibrationCDU pump isolation.
Cable entryHose and cable entries for racks and immersion tanks.
Modules and skids travel by road and sea before they run, and every power and fiber route crosses a wall, floor or container.
AntivibrationHat mounts under modules to protect equipment from transit shock.
Cable entryModule wall and floor cable entries.
Cable entryModular systems, entry plates and splitting systems for pre-terminated cables.
One partner per equipment package
Most equipment packages need all three. Trelleborg brings antivibration, sealing and cable entry expertise together, with joint samples and one point of contact for your engineering team.
Conical, leveling, cylindrical and sandwich mounts, elastomer pads, flexible pipe connectors and transport mounts that keep vibration and shock out of structures and equipment.
O-rings, rotary and lip seals, flat gaskets and spring-energized seals for fuel, oil, coolant, compressor and liquid-cooling circuits.
Entry plates, grommets and splitting systems for pre-terminated cables, rated IP66/67 and UL94 V-0, for switchgear, UPS, battery storage and modules.
Example: CDU pump skid
Antivibration – pump isolation
Sealing – quick-disconnect and pump seals
Cable entry – hose and cable entries
In service today
[Wording pending customer approval]
[Wording pending customer approval]
[Wording pending customer approval]
Our application engineers develop solutions with customers for equipment that is new to data centers – including on-site gas engines, heat-recovery heat pumps, rotary UPS, seismic restraint and integrated rack transport.
Contact
Tell us about your equipment or project. Your request goes directly to the data center team for your region.
Meet us in 2027
[Event name, city, dates, stand number]
Your request has reached our data center team. An application engineer will contact you within [X] working days.
In the meantime, download the data center brochure.